Knucklehead

High-quality cast aluminum construction Sold in pairs with adapters to fit 35mm, 39mm and 41mm fork tube outer diameters Available in polished aluminum or satin black finishes

Stock Knuckle replacement cam For stock motors and restoring an older classic engine, this is the cam to use Made in the U.S.A. Intake: Open: 13 degrees /Close: 44 degrees /Duration @.053: 234 degrees /Valve Lift: .348 Exhaust Open: 47 degrees...

"S" GRIND CAM Bolt-in performance cam Smooth idle, strong pull to 6000 rpm This cam is the Knuckle equivalent of a "B" cam in a Pan/Shovel motor Made in the U.S.A. Intake: Open: 27 degrees /Close: 55 degrees /Duration @.053: 262 degrees /Valve...

Chrome, one-piece design; measures 31" long All-steel baffle construction Sold individually Muffler requires mounting clamps; sold separately Made in the U.S.A. California Warning : The California Air Resources Board (“CARB”) does not...

Axle Kit

Features JIMS transmission parts and gasket set Includes standard size race, snap rings, clips, shift shaft, countershaft, seals and bushings; does not include bearings Made in the U.S.A.

6V generator w/standard regulator; 15A High-quality construction and components; manufactured by the same company that supplies OEM Armature is balance wound, and the epoxy-bonded wires are fused to the commutator; hard maple wire wedges secure...

Kit includes oil pump, universal cover with top and bottom feeds, mounting bolts, supply and return gears, drive shaft with keys and snap rings, check ball and spring, pressure relief valve and spring, check ball and release valve cover screws...

Reproduction of hardened 3/8"-20 bolts Complete with chip curls at bottom of the socket hole Parkerized and hardened Made in the U.S.A.

Kit includes cam and gear shaft bushings/bearings, along with lock pins and thrust plate, OEM #s 275, 25551-36, 35581-36, 25582-36, 25597-36, 25785-30A Made in the U.S.A.

Bushing is made from solid bronze bar stock Machined in one operation with a tolerance of .0002" Feature a lead-in for ease of installation Sold each Made in the U.S.A.

Includes copper gasket, nut and lock washer Cad-plated Repl. OEM #27375-29, 27376-28, 7045, 7793

Kit includes 3/8" fiber insulator block and gaskets Designed to reduce the risk of boiling fuel in the carb Made in the U.S.A. Repl. OEM #29250-55

Exact reproduction of the original H-D support brackets OEM #27432-36 Used to support the Linkert carburetor Made in the U.S.A.

Exact reproduction of the original H-D support brackets OEM #27431-41 Used to support the Linkert carburetor Made in the U.S.A.

Chromed Cat Eye dash cover and zinc-plated base Plate is for custom applications on 66-84 Shovelhead Dash cover and base plate sold separately Base plate for 66-84 OEM tanks and Fat Bob-style tanks

Chrome finish Left Side 32-1/2' L Universal mount, include brackets Made in the U.S.A.

12V horns emit loud (113 dB) signal 4" diameter; universal mount Sold each

High-strength steel kickstands with a brilliant chrome finish Replaces OEM kickstands perfectly Overstock kickstand lengths are for bikes with longer suspension than stock Understock kickstands are for bikes with lowered suspension NOTE:...

Cad-plated reproduction of pivot screws and nuts Used on clutch and brake levers Made in the U.S.A.

Reproduction of original bronze bushings Sold in pairs Made in the U.S.A.

Complete with rivets

Chrome rod end fits "mousetrap" clutch releases

Replacement inspection covers available in either chrome or gloss black Fit stock H-D's as well as Paughco outer primary covers Made in the U.S.A.

Chromed 1/8" thick steel exhaust hangers Available in assorted lengths and configurations Sold individually

Quality reproduction of original parts Kits include axle nut, sleeve nut, cotter pin and axle nut washer Made in the U.S.A.

Beautifully chrome-plated accessory Allows easier operation of shut off valve Made in the U.S.A.

Chrome-plated valve fitting kit is designed to use flexible hoses Made in the U.S.A. NOTE: Not for Linkert carb.

Include circuit breaker drive gear, idler gear assembly and circuit breaker shaft gear with shims Circuit breaker gear shaft and idler gear shaft sold separately standard clockwise rotation Made in the U.S.A.

For all Knucklehead generators w/updated end plate (four-hole) 6V standard regulator with black finish for models with generator updated to the 58-64 two-brush generator Updated end plate has an extra set of mounting holes to align the fins on...

Reproduction of throttle and spark plunger Kit includes two plungers Made in the U.S.A.

For 41-47 74" Knucklehead; .791" wrist pin High-quality, heavy-duty rod set comes complete and ready to install Set includes front and rear rods, crankpin and nuts, steel cages and roller bearings Rods are forged and heat-treated, .120" wider...

Increases peak spark voltage by 20% or more Improves starting, stops high-speed misfires, increases mileage and overall performance 1.3 ohm/6V application/dual-fire 30,000V output Available in black, red or chrome body

Five-terminal ignition switch for 36-47 (incl. "tin-" style cap) Replacement ignition and light switch with lock for Fat Bob-style dash panels Meet or exceed all OEM specifications Includes two flat keys

Precision machined exact duplicates of the original intake manifold seals, nuts and nipples Cad-plated intake manifold nuts for O.H.V. 61"/74" engines; repl. OEM #270590-40 Brass intake manifold seals for O>H>V> 61"/74" engines; repl....

For 36-48 Knucklehead Kit includes three 3/8"-16 bolts, OEM #4293; four 5/16" bolts, OEM #3974; one nut, OEM #7835; four 5/16"-24 nuts, OEM #7752 and four lock washers OEM #7040 Available in cadmium or parkerized finish Made in the U.S.A.

Kit includes chrome-plated bolt, pedal bushing, spring washer and lock washer

Bushing kit w/O-ring for 37-47 Knucklehead; repl. OEM #33288-37, 11101

Feature a heavy-duty construction made from brass with a steel liner core Available in polished brass or chromed finish Includes bushing and clip Sold each

Precision-machined replacement shaft Extended kick starter is extended .0750" to allow more space between kicker arm and exhaust; keeps exhaust from getting scuffed Made in the U.S.A.

For use on lowered bikes Allows you to adjust the angle of your kickstand quickly and easily Sold each Made in the U.S.A.

Made from 4140 heat-treated steel for maximum wear-resistance Rounded teeth for smoother, quieter rolling Reinforced stop-peg prevents breakage into the transmission 16T kicker gear; kit includes gasket, key and lock tab; repl. OEM #s 33350-36,...

For 40-47 Knucklehead/Flathead, std.; repl. OEM #24621-40

Chrome brake drum/51T sprocket includes dust cover

Waterproof mechanical stoplight switch attaches to rear brake rod or brake linkage and frame tube Ideal for custom applications

Chromed steel bracket allows use of 68-84 style Big Twin clutch cables on Panhead models

Made in the U.S.A.

High-quality drop-in oil filter

Feature points, condenser and mechanical advance assemblies pre-installed Chrome finish Sold each

For 35-47 FL, 37-52 45" WL, Servi Car 37-50 Chrome replacement stoplight switch Also works great for custom applications

High-quality brake shoes; sold in pairs

Kit includes foam float, needle and seat, gaskets, springs and bushings

16" x 3" 40-spoke wheels feature chrome steel rims, chrome spokes and chrome steel hubs (unless noted) Fully assembled and trued with bearings installed and end play set Front or Rear Wheel Available in most applications Uses OEM mounting hardware

Used to rebuild S&S and stock connecting rods Includes hardened steel rod bearing races and bronze wrist pin bushings Requires finish sizing after installation Made in the U.S.A.

Made from 52100 aerospace-quality Timken® bearing stock Sold as a set Made in the U.S.A.

• Rubber driver pegs with zinc-plated steel inserts
• Sold in pairs

• 3/32"; repl OEM #6754
• Sold Each
• Made in the U.S.A

Feature a heavy steel contoured seat base with a black finish Include adjustable front seat hinge and two rear mount studs for springs; order springs separately 1" x 3/16" welded center bar Studs are 5/16" x 7/8" L and 6" center-to-center (small...

Feature a heavy steel contoured seat base with a black finish Include adjustable front seat hinge and two rear mount studs for springs; order springs separately 1" x 3/16" welded center bar Studs are 5/16" x 7/8" L and 6" center-to-center (small...

Feature a heavy steel contoured seat base with a black finish Include adjustable front seat hinge and two rear mount studs for springs; order springs separately 1" x 3/16" welded center bar Studs are 5/16" x 7/8" L and 6" center-to-center (small...

Replacement derby covers available in either chrome or gloss black Fit stock H-D's as well as Paughco outer primary covers Made in the U.S.A.

Forged, chrome-plated arm is 101/4" long overall, and includes pinch bolt NOTE: Please note location of pinch bolt; this kicker arm will only work on kickstart shafts that feature a pinch bolt groove machined completely around the shaft.

OEM #67026-36 Length 31" Top Nut Size 3/4"-20 Replacement speedometer cables come in your choice of stainless steel with non-abrasive clear coat or black vinyl covering Available for transmission-drive Harley models The entire line of Drag...

For 36-47 Paughco rigid Knucklehead frames Heavy-duty construction Easy bolt-in application Steel construction; chrome finish Made in the U.S.A.

For FX, FXR, FL AND XL MODELS Visor for 7" headlight; repl. OEM #67752-77T Sold Each Visors are easy to install; add a custom look Chrome steel construction